Skip to content

Viking Dishwasher error code

Viking Dishwasher 4-2 Error Code

What 4-2 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.

Display readoutDallas

4-2Dishwasher display code

01

4-2

What it means

4-2 is described as “wash heater error”.

4-2: wash heater error.

02

Safe for owners

Check first

Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.

03

Likely cause

On most Viking appliances, 4-2 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.

04

When to book

If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.

05

About 4-2

Viking describes code 4-2 on this dishwasher with the wording “wash heater error”.

Code4-2
Applies toElectronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010)
MeaningWash heater error: wash heater current sense out of range.
Control generationLegacy
Service referenceThe element is 120 V, 12 ohm, 10 amp, 1200 watt.
06

Before applying the instructions

The control reference provides the listed equipment.

  • E-series units use a 1200 watt heater; non-E 325/450 models use 1400 watt.
07

Work for a technician

The fault reference details the listed service work.

  • The dishwasher uses a flow-through heater that heats water as it passes through its center.
  • Check wires between the main control and the wash heater.
  • Unplug the gray wire on P12 and check for 12 ohms to neutral; 0 ohms means check wiring to the heater.
08

Conditions behind the message

The appliance reference details the causes below.

  • A defective temperature sensor is also listed as a possible cause.
09

Other codes in the appliance documentation

  • 3-3 — Drain pump error: drain pump current sense out of range.
  • 3-4 — Motor status error: motor control reports an operation failure most likely caused by the motor.
  • 4-1 — Temperature sensor error: temperature sensor reads out of range.
10

Safe checks and useful observations

Make a note of changes during dishwasher draining during the initial service discussion. Consult the owner manual before carrying out accessible cleaning an owner-accessible filter. Leave any enclosed electrical connections alone when preparing for inspection.

11

Getting repair help in Dallas

For the initial discussion, have the serial and model identification and describe any changes during operation. Assessment precedes repair decisions; the repair proposal includes a written estimate before you authorize any repairs. Contact the service team.

12

Sources

13

Questions about this code

What does 4-2 mean on a Viking dishwasher?

The manual describes the indication as “wash heater error”. Match the model and control version before following the instructions.

What should I do before requesting dishwasher service?

Provide an account of any obstruction around the door as part of the reported problem description. Explain if the appliance stops during the chosen cycle. Leave any enclosed electrical connections alone when preparing for inspection.

15

Dishwasher models on file

All models

16

Work order

Book a Viking technician

Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.

Request a Viking repair

Ready to get your Viking appliance working again?

Diagnosis first, a written estimate before any work, parts matched to the full model number.

(415) 853-4850 Book a Repair