Viking Dishwasher error code
Viking Dishwasher 4-1 Error Code
What 4-1 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.
4-1
What it means
4-1 is described as “temperature sensor error”.
4-1: temperature sensor error.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, 4-1 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About 4-1
On a Viking dishwasher, the 4-1 indication has this documented meaning: “temperature sensor error”.
| Service reference | The NTC sensor reads about 47k ohms at 77 F ambient; resistance drops as water warms. |
|---|---|
| Meaning | Temperature sensor error: temperature sensor reads out of range. |
| Applies to | Electronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010) |
| Code | 4-1 |
| Control generation | Legacy |
Technical fault guidance
The diagnostic notes give the following procedures.
- Check for wires disconnected from the temperature sensor.
- VDB200: check connections and check for 47k ohms at ambient.
- The control board monitors the water temperature sensor at P8-3 to P8-4.
- If no resistance is found check wiring; if wiring is OK replace the sensor.
Check a different display code
What to check without opening panels
Note changes in dish cleaning alongside the chosen operating settings. Mention the cycle in which the result changed. Leave the enclosed control circuits intact for the service professional.
Preparing for a Dallas visit
At booking, provide the appliance identification and symptom notes and describe any changes during operation. Initial checks establish the repair proposal; you receive a written repair estimate, and approval is needed before repair work. Book an assessment.
Sources
- Viking Preferred Service Service Manual Built-In Dishwasher FDB451 VDB451, SMK-0005, Aug 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher FDB301 RDDB201 RDDB301 VDB301, SMK-0006, Apr 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB325 VDB450 (from 5/26/2010) VDB325E VDB450E, SMK-0003, Apr 2011 (Error Codes, pp.19-21), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB200, SMK-002, May 2010 (Fail Codes, p.13), hosted on uncleharrywizard.com
Questions about this code
What does 4-1 mean on a Viking dishwasher?
The manual describes the indication as “temperature sensor error”. Match the model and control version before following the instructions.
What should I do before requesting dishwasher service?
Explain whether the wash cycle finishes alongside the chosen operating settings. Describe if the equipment stops during the selected cycle. Keep the electrical service covers undisturbed until a repair technician has seen the equipment.
Dishwasher models on file
- DFUD04224-inch built-in dishwasherDesigner Series Undercounter Dishwasher.
- FDWU52424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
- FDWU524WS24-inch panel-ready built-in dishwasher with water softener24-inch Dishwasher with Water Softener and Optional Custom Panel.
- FDWU72424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.