Skip to content

Viking Dishwasher error code

Viking Dishwasher 1-4 Error Code

What 1-4 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.

Display readoutDallas

1-4Dishwasher display code

01

1-4

What it means

1-4 is described as “diverter timeout”.

1-4: diverter timeout.

02

Safe for owners

Check first

Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.

03

Likely cause

On most Viking appliances, 1-4 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.

04

When to book

If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.

05

About 1-4

Viking describes code 1-4 on this dishwasher with the wording “diverter timeout”.

MeaningDiverter timeout: main control activates the diverter but gets no feedback that the correct position was reached.
Applies toElectronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010)
Control generationLegacy
Code1-4
06

Internal checks from the manual

The technical reference identifies these internal checks.

  • VDB200: verify diverter resistance and wiring.
  • Check the wires between the control board and the diverter.
  • A built-in monitoring switch in the diverter sends 120 VAC back to control board P6-5; how long it stays closed shows the position.
  • The wash diverter sends water to the upper or lower arm during the wash cycle.
  • The diverter motor should read approximately 2.7k ohms between P6-2 and neutral; if wiring is proper and reading wrong, replace the diverter.
07

Further fault descriptions

  • 1-1 — Moisture sensor disconnect: moisture sensor reads out of normal range (wires disconnected, defective sensor or control board).
  • 2-1 — Pressure sensor disconnect: pressure sensor reads out of normal range (low).
  • 1-2 — Motor control status error on the variable-speed wash motor (motor control reports a motor operation failure or motor current out of range).
08

Before requesting a visit

Document the flashing dishwasher indicators when preparing for appliance inspection. Note a message that returns during usual control use. Leave the electrical service covers undisturbed while recording the concern.

09

Repair appointments in Dallas

For the visit, prepare the appliance identification details and describe any changes while the appliance runs. Repair decisions follow diagnosis; you receive a written repair estimate with no repairs started without approval. Request appliance service.

10

Sources

11

Questions about this code

What does 1-4 mean on a Viking dishwasher?

The manual describes the indication as “diverter timeout”. Match the model and control version before following the instructions.

What should I do before requesting dishwasher service?

Write down any obstruction around the door as part of the reported problem description. Give details of whether water remains after the wash. Leave the appliance service panels intact for the service professional.

13

Dishwasher models on file

All models

14

Work order

Book a Viking technician

Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.

Request a Viking repair

Ready to get your Viking appliance working again?

Diagnosis first, a written estimate before any work, parts matched to the full model number.

(415) 853-4850 Book a Repair