Skip to content

Viking Dishwasher error code

Viking Dishwasher 1-2 Error Code

What 1-2 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.

Display readoutDallas

1-2Dishwasher display code

01

1-2

What it means

1-2 is described as “motor control status error on the variable-speed wash motor”.

1-2: motor control status error on the variable-speed wash motor.

02

Safe for owners

Check first

Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.

03

Likely cause

On most Viking appliances, 1-2 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.

04

When to book

If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.

05

About 1-2

The 1-2 indication on a Viking dishwasher is described in the manual as “motor control status error on the variable-speed wash motor”.

Control generationLegacy
Applies toElectronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010)
Code1-2
MeaningMotor control status error on the variable-speed wash motor (motor control reports a motor operation failure or motor current out of range).
06

Internal checks from the manual

The diagnostic notes list the listed service work.

  • The 200 Series dishwasher uses a single speed, capacitor assist wash motor.
  • 200 Series wash motor reads 6.3 ohms between P5-1 and P5-2 in the control board test point list.
  • Check wires between the motor control and the motor.
  • VDB200: check that the rotor turns freely and check winding resistances.
  • VDB200 (single-speed motor): check wires between motor and start capacitor.
07

Other codes in the appliance documentation

  • 2-1 — Pressure sensor disconnect: pressure sensor reads out of normal range (low).
  • 1-4 — Diverter timeout: main control activates the diverter but gets no feedback that the correct position was reached.
  • 1-5 — Drain error: water still in the tub after a drain (pressure sensor never reaches empty level, or water detected on non-pressure-sensor models).
08

Notes to prepare at home

Note the flashing dishwasher indicators when arranging a visit. Note a message that returns during usual control use. Leave all internal wiring connections untouched during owner observations.

09

Preparing for a Dallas visit

To prepare, record the appliance identification and symptom notes and mention whether the reported problem returns. Assessment precedes decisions about the repair; you receive a written estimate, and repairs require your approval. Contact the service team.

10

Sources

11

Questions about this code

What does 1-2 mean on a Viking dishwasher?

The manual describes the indication as “motor control status error on the variable-speed wash motor”. Match the model and control version before following the instructions.

What should I do before requesting dishwasher service?

Provide details about usual dishwasher door closure alongside the chosen operating settings. Record whether the chosen wash cycle finishes. Leave the unit service panels undisturbed until a technician has seen the equipment.

13

Dishwasher models on file

All models

14

Work order

Book a Viking technician

Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.

Request a Viking repair

Ready to get your Viking appliance working again?

Diagnosis first, a written estimate before any work, parts matched to the full model number.

(415) 853-4850 Book a Repair