Viking Dishwasher error code
Viking Dishwasher 2-1 Error Code
What 2-1 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.
2-1
What it means
2-1 is described as “pressure sensor disconnect”.
2-1: pressure sensor disconnect.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, 2-1 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About 2-1
On a Viking dishwasher, the 2-1 indication has this documented meaning: “pressure sensor disconnect”.
| Applies to | Electronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011) |
|---|---|
| Service reference | Empty sump should read 0.5-0.8 VDC between P8-6 (yellow) and P8-5 (ground). |
| Control generation | Legacy |
| Code | 2-1 |
| Meaning | Pressure sensor disconnect: pressure sensor reads out of normal range (low). |
What can trigger the signal
The manual details the following causes.
- Next possible causes: defective pressure sensor, then defective sensor harness.
Internal checks from the manual
The repair instructions set out the technical actions below.
- Verify the pressure sensor is properly connected.
- The pressure sensor is mounted to the sump retainer ring.
- Pressure sensor wiring: 5 volts DC input and 0.5-3.5 volts DC output at the control board.
Other signals to look up
- 1-5 — Drain error: water still in the tub after a drain (pressure sensor never reaches empty level, or water detected on non-pressure-sensor models).
- 2-5 — Level/siphon error: abnormal pressure-sensor change (drains too fast or fills too fast).
- 1-3 — Motor control communication error: main control cannot communicate with the motor control.
What to check without opening panels
Describe the exact wash-control message as part of the symptom description. Note a message that returns during usual control use. Leave the concealed appliance wiring undisturbed until a technician has seen the appliance.
Preparing for a Dallas visit
At booking, provide the rating label information and any code and explain which owner checks were attempted. Initial checks establish the repair proposal; you receive a written repair estimate, so you can decide before repairs proceed. Send a service request.
Sources
- Viking Preferred Service Service Manual Built-In Dishwasher FDB451 VDB451, SMK-0005, Aug 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB325 VDB450 (from 5/26/2010) VDB325E VDB450E, SMK-0003, Apr 2011 (Error Codes, pp.19-21), hosted on uncleharrywizard.com
Questions about this code
What does 2-1 mean on a Viking dishwasher?
The manual describes the indication as “pressure sensor disconnect”. Match the model and control version before following the instructions.
What should I do before requesting dishwasher service?
Give details of normal dishwasher door closure before deciding on repair work. Give details of if the equipment stops during the chosen cycle. Keep any enclosed electrical connections undisturbed until an appliance technician has seen the unit.
Dishwasher models on file
- DFUD04224-inch built-in dishwasherDesigner Series Undercounter Dishwasher.
- FDWU52424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
- FDWU524WS24-inch panel-ready built-in dishwasher with water softener24-inch Dishwasher with Water Softener and Optional Custom Panel.
- FDWU72424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.