Viking Dishwasher error code
Viking Dishwasher BOTH LEDS FLASH Error Code
What BOTH LEDS FLASH means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.
Display readoutDallas
BOTH LEDS FLASHDishwasher display code
BOTH LEDS FLASH
What it means
BOTH LEDS FLASH is described as “water detected in the base pan”.
BOTH LEDS FLASH: water detected in the base pan.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, BOTH LEDS FLASH points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About BOTH LEDS FLASH
The BOTH LEDS FLASH indication on a Viking dishwasher is described in the manual as “water detected in the base pan”.
| Meaning | Both LED1 and LED2 flash continuously: moisture sensor detects water in the base pan (overflow or leak, or defective sensor). |
|---|---|
| Code | BOTH LEDS FLASH |
| Applies to | Electronic-control built-in dishwashers: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010) |
| Control generation | Legacy |
Work for a technician
The service guidance details the technical actions below.
- Any moisture on the sensor stops filling, runs the drain pump and signals an error code.
- VDB200: check the base pan for water and check the sensor for 175k ohms.
Possible causes in the documentation
The manual identifies these possible causes.
- Water in the base pan from overflow or leak is the first listed cause.
Further fault descriptions
- F2 — Overfilling: too much water (pressure sensor or float); if not evacuated within 60 seconds the program is interrupted and the drain pump runs.
- F1 — Temperature stop fault: temperature rise under 50F in five minutes; program leaves heating stage and continues. Shown only in service menu.
- F3 — Thermistor fault: thermistor interrupted or above 176F; program leaves heating stage and continues. Shown only in service menu.
What to check without opening panels
Tell the technician about whether the wash cycle finishes when preparing for appliance inspection. Note whether the chosen wash cycle finishes. Keep the appliance service panels untouched while checking external controls.
Repair appointments in Dallas
To prepare, record the serial and model identification and describe any differences in normal use. Assessment precedes repair decisions; the findings lead to a written estimate, with repair work subject to your approval. Contact the service team.
Sources
- Viking Preferred Service Service Manual Built-In Dishwasher FDB451 VDB451, SMK-0005, Aug 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher FDB301 RDDB201 RDDB301 VDB301, SMK-0006, Apr 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB325 VDB450 (from 5/26/2010) VDB325E VDB450E, SMK-0003, Apr 2011 (Error Codes, pp.19-21), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB200, SMK-002, May 2010 (Fail Codes, p.13), hosted on uncleharrywizard.com
Questions about this code
What does BOTH LEDS FLASH mean on a Viking dishwasher?
The manual describes the indication as “water detected in the base pan”. Match the model and control version before following the instructions.
What should I do before requesting dishwasher service?
Tell the repair technician about normal dishwasher door closure with the model identification. Write down whether the chosen wash cycle finishes. Keep the unit service panels undisturbed until a service technician has seen the equipment.
Dishwasher models on file
- DFUD04224-inch built-in dishwasherDesigner Series Undercounter Dishwasher.
- FDWU52424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
- FDWU524WS24-inch panel-ready built-in dishwasher with water softener24-inch Dishwasher with Water Softener and Optional Custom Panel.
- FDWU72424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.