Viking Dishwasher error code
Viking Dishwasher ALL LEDS BUT START FLASH Error Code
What ALL LEDS BUT START FLASH means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.
Display readoutDallas
ALL LEDS BUT START FLASHDishwasher display code
ALL LEDS BUT START FLASH
What it means
ALL LEDS BUT START FLASH is described as “AC power loss during a running cycle”.
ALL LEDS BUT START FLASH: AC power loss during a running cycle.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, ALL LEDS BUT START FLASH points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About ALL LEDS BUT START FLASH
For a Viking dishwasher, code ALL LEDS BUT START FLASH carries the documented description “AC power loss during a running cycle”.
| Applies to | Electronic-control built-in dishwashers: FDB451/VDB451 (SMK-0005, 2012); FDB301/RDDB201/RDDB301/VDB301 (SMK-0006, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010) |
|---|---|
| Meaning | All LEDs except Start (and Run on select models) flash continuously: AC power loss occurred during a running cycle. |
| Control generation | Legacy |
| Code | ALL LEDS BUT START FLASH |
Checks available to the owner
The care instructions set out the listed checks.
- Reset by pressing and holding the Start button for 3 seconds (four seconds on VDB200).
What can trigger the signal
The appliance reference provides the listed fault conditions.
- Cause listed is power lost during a cycle.
Service procedures
The service guidance describes these diagnostic checks.
- VDB200 action: reset and test.
Other messages and alarms
- F3 — Thermistor fault: thermistor interrupted or above 176F; program leaves heating stage and continues. Shown only in service menu.
- F1 — Temperature stop fault: temperature rise under 50F in five minutes; program leaves heating stage and continues. Shown only in service menu.
- BOTH LEDS FLASH — Both LED1 and LED2 flash continuously: moisture sensor detects water in the base pan (overflow or leak, or defective sensor).
Before requesting a visit
Give details of dishes remaining wet or soiled when preparing for appliance inspection. Mention the cycle in which the result changed. Leave the internal electrical connections untouched during accessible care.
Repair appointments in Dallas
For the service professional, collect the exact model and observed symptoms, with a description of the trouble. The technician investigates the operating concern first; a written repair estimate describes the proposal, and nothing is repaired until you approve. Request appliance service.
Sources
- Viking Preferred Service Service Manual Built-In Dishwasher FDB451 VDB451, SMK-0005, Aug 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher FDB301 RDDB201 RDDB301 VDB301, SMK-0006, Apr 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB325 VDB450 (from 5/26/2010) VDB325E VDB450E, SMK-0003, Apr 2011 (Error Codes, pp.19-21), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB200, SMK-002, May 2010 (Fail Codes, p.13), hosted on uncleharrywizard.com
Questions about this code
What does ALL LEDS BUT START FLASH mean on a Viking dishwasher?
The manual describes the indication as “AC power loss during a running cycle”. Match the model and control version before following the instructions.
What should I do before requesting dishwasher service?
Report usual dishwasher door closure as part of the symptom description. Report if the unit stops during the selected cycle. Keep the electrical service covers undisturbed until a service technician has seen the appliance.
Dishwasher models on file
- DFUD04224-inch built-in dishwasherDesigner Series Undercounter Dishwasher.
- FDWU52424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
- FDWU524WS24-inch panel-ready built-in dishwasher with water softener24-inch Dishwasher with Water Softener and Optional Custom Panel.
- FDWU72424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.