Viking Dishwasher error code
Viking Dishwasher 5-5 Error Code
What 5-5 means on a Viking dishwasher, the checks that are safe to make and when it needs a technician.
5-5
What it means
5-5 is described as “internal error”.
5-5: internal error.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, 5-5 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About 5-5
The 5-5 indication on a Viking dishwasher is described in the manual as “internal error”.
| Meaning | Internal error: main control or user interface detects a board-level failure. |
|---|---|
| Code | 5-5 |
| Applies to | Electronic-control built-in dishwashers; displayed as flashes of POTS/PANS light (first digit) then NORMAL WASH light (second digit). Documented for: FDB451/VDB451 (SMK-0005, 2012); VDB325/VDB450 from 5/2010 and 325E/450E (SMK-0003, 2011); VDB200 (SMK-002, 2010) |
| Control generation | Legacy |
Internal fault investigation
The technical reference includes these internal checks.
- VDB200: press and hold the Start button for four seconds; if it repeats, replace the controls.
Listed causes
The manufacturer guidance includes these cause notes.
- Causes listed are defective main control and defective user interface.
Further fault descriptions
- F2 — Overfilling: too much water (pressure sensor or float); if not evacuated within 60 seconds the program is interrupted and the drain pump runs.
- 5-4 — Current sense error: main control reads current draw when no loads are active.
- F1 — Temperature stop fault: temperature rise under 50F in five minutes; program leaves heating stage and continues. Shown only in service menu.
Owner observations and safe checks
Include information about whether wash controls respond alongside the chosen operating settings. Note a message that returns during usual control use. Leave the enclosed control circuits untouched during owner observations.
Repair appointments in Dallas
For the visit, prepare the exact model and observed symptoms, plus what happened before the fault. A diagnosis guides the repair discussion; the suggested work comes with a written estimate, and approval is needed before repair work. Send a service request.
Sources
- Viking Preferred Service Service Manual Built-In Dishwasher FDB451 VDB451, SMK-0005, Aug 2012 (Fail Codes, pp.12-13), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB325 VDB450 (from 5/26/2010) VDB325E VDB450E, SMK-0003, Apr 2011 (Error Codes, pp.19-21), hosted on uncleharrywizard.com
- Viking Preferred Service Service Manual Built-In Dishwasher VDB200, SMK-002, May 2010 (Fail Codes, p.13), hosted on uncleharrywizard.com
Questions about this code
What does 5-5 mean on a Viking dishwasher?
The manual describes the indication as “internal error”. Match the model and control version before following the instructions.
What should I do before requesting dishwasher service?
Write down whether the wash cycle finishes when preparing for appliance inspection. Describe if the equipment stops during the chosen cycle. Keep all concealed wiring connections untouched while checking external controls.
Dishwasher models on file
- DFUD04224-inch built-in dishwasherDesigner Series Undercounter Dishwasher.
- FDWU52424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
- FDWU524WS24-inch panel-ready built-in dishwasher with water softener24-inch Dishwasher with Water Softener and Optional Custom Panel.
- FDWU72424-inch panel-ready built-in dishwasher24-inch Dishwasher with Optional Custom Panel.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.