Viking Range error code
Viking Range F01 Error Code
What F01 means on a Viking range, the checks that are safe to make and when it needs a technician.
F01
What it means
F01 is described as “door latch fault”.
F01: door latch fault.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, F01 points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About F01
On a Viking range, the F01 indication has this documented meaning: “door latch fault”.
| Code | F01 |
|---|---|
| Meaning | Door latch: door lock not in unlocked position during cook or locked position during clean. Critical (priority A). Range: Clean light flashes once, Cycle light off. |
| Applies to | Ranges and wall ovens with EOC4 control; wall ovens with TOD2/TOD3 clock show the F code, ranges show it as Cycle/Clean light flashes |
Precautions for the reported condition
The appliance reference lists these warnings.
- Priority A: critical error, cancels current cycle and turns off all elements.
The signal during operation
The operating guidance sets out these signal descriptions.
- In a clean cycle the control cancels and tries to lock the door; in a cook cycle it tries to cycle the motor to the unlocked state.
Service procedures
The fault reference includes these service checks.
- Turn cycle off, power down and correct the door lock issue.
Further fault descriptions
- F03 — Cooling fan Hall-effect: control not receiving a square wave in the allowed frequency range. Cancels bake or clean. Range: Clean on, Cycle flashes 3.
- F06 — Invalid model header: model header undefined, read at power-up; control inoperable. Range: Clean on, Cycle flashes 2.
- F04 — Meat probe input shorted. Cancels cook-by-probe operation (priority B, non-critical).
Preparing for an appliance assessment
Write down the selected cooking settings without repeating unsafe operation. Identify the affected cooking area in the service request. Leave the electrical service covers undisturbed until a technician has seen the appliance.
Repair appointments in Dallas
For the service technician, collect the equipment model and any fault message and mention whether the operating concern returns. A diagnosis guides the repair discussion; a written estimate follows, and repairs require your approval. Contact the service team.
Sources
Questions about this code
What does F01 mean on a Viking range?
The manual describes the indication as “door latch fault”. Match the model and control version before following the instructions.
What should I do before requesting range service?
Include information about the chosen heating mode during the initial service discussion. Say if trouble begins before or after heating starts. Leave the appliance service panels undisturbed until a repair technician has seen the unit.
Range models on file
- RVER330130-inch freestanding radiant electric range with convection oven30-inch Self-Cleaning Electric Range.
- RVIR33030-inch freestanding induction range with self-cleaning electric oven30-inch Induction Range.
- TVDR36136-inch dual-fuel range with four gas burners and electric oven36-inch Tuscany Dual Fuel Range.
- TVDR48148-inch dual-fuel double-oven range48-inch Tuscany Dual Fuel Range.
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.