Viking Induction cooktop error code
Viking Induction Cooktop 6 FLASHES Error Code
What 6 FLASHES means on a Viking induction cooktop, the checks that are safe to make and when it needs a technician.
Display readoutDallas
6 FLASHESInduction cooktop display code
6 FLASHES
What it means
6 FLASHES is described as “incompatible cookware for induction”.
6 FLASHES: incompatible cookware for induction.
Safe for owners
Check first
Switch the appliance off at the breaker for one minute, restore power and note whether the code returns. Nothing else should be opened or removed.
Likely cause
On most Viking appliances, 6 FLASHES points to a control, sensor, ignition, heating, door-lock, water or drain issue that should be confirmed against the full model number before parts are replaced.
When to book
If the code comes back after the power reset, or there is water, a burning smell or a tripped breaker, stop using the appliance and book a visit with the full model number.
About 6 FLASHES
On a Viking induction cooktop, the 6 FLASHES indication has this documented meaning: “incompatible cookware for induction”.
| Code | 6 FLASHES |
|---|---|
| Meaning | Induction LED flash code: 6 consecutive flashes = incompatible cookware for induction. |
| Control generation | Legacy |
| Service reference | Cookware diameter should be between 5 in. (small burners) and 12 in. (larger burners). |
| Applies to | Built-in electric radiant/induction cooktop (F20111C) and built-in induction rangetop (F20114) Use & Care Internal Error Codes table; LED indicators with brief interval between flash groups |
Owner troubleshooting
The operating manual identifies the listed checks.
- If flashing continues after adjusting cookware per the manual, call a service technician.
Work for a technician
The diagnostic notes describe these service checks.
- Use cookware with a magnetic, flat bottom; check with a magnet (if it sticks to the bottom it is suitable).
Cause notes
The manual describes the causes below.
- Unsuitable for induction: stainless steel pans with aluminum bottom, pottery, aluminum pans.
Other signals to look up
- Er47 — LEDs flash 5 times then pause and 7-digit display shows Er47: wrong configuration program (C1-C6) in the interface adapter board.
- 5 FLASHES — Induction LED flash code: 5 consecutive flashes = inside ambient temperature too high.
- 3 FLASHES — Induction LED flash code: 3 consecutive flashes = power device temperature sensor malfunction.
Safe checks and useful observations
Provide details about how heating differs from normal when preparing for appliance inspection. Keep the chosen cooking function with the details for assessment. Keep the concealed appliance wiring untouched while checking external controls.
Repair appointments in Dallas
For the visit, prepare the complete model and serial identification, plus what happened before the fault. Assessment precedes decisions on proposed work; a written repair estimate follows, and nothing is repaired until you approve. Contact the service team.
Sources
Questions about this code
What does 6 FLASHES mean on a Viking induction cooktop?
The manual describes the indication as “incompatible cookware for induction”. Match the model and control version before following the instructions.
What should I do before requesting induction cooktop service?
Tell the technician about the affected cooktop function when arranging a visit. Report the setting in use when trouble began. Keep the internal electrical components undisturbed until a repair technician has seen the appliance.
Induction cooktop models on file
Work order
Book a Viking technician
Read the model and serial number off the rating plate and add them to the request — the technician checks parts for that exact unit before the visit.
- Phone(415) 853-4850
- Emailservice
@vikingdallas .com - HoursMon–Sat 8:00 AM – 7:00 PM
- Service area11 counties across Dallas–Fort Worth
Request a Viking repair
Ready to get your Viking appliance working again?
Diagnosis first, a written estimate before any work, parts matched to the full model number.